11,00 mm-FRESA MICROGRANO DIN6528N 4Z-
07,00 mm-END MILL MICROGRAIN DIN6528N 4Z
- 6528
- N
- Micrograin
- 7.00
- 7.00
- 60.00
- 16.00
- 4
- 30º
- Flat
- 1
- Steel
- Aluminium-Magnesium
- Synthetic-Plastics
- Stainless
- Cast Iron
- Ferritic / Martensitic Stainless (<320 HB / <850 N/mm2)
- Austenitic Stainless (<250 HB / <850 N/mm2)
- Titanium Alloys
- Cast Iron (<200 HB / <700 N/mm2)
- Cast Iron (200-300 HB / 700-1000 N/mm2)
- Hard-Plastics
- Alloyed Steel (<300 HB / <1000 N/mm2)
- Treated / Heat-Treatable Alloyed Steel (300-400 HB / 1000-1300 N/mm2)
- Short Chip Copper-Bronze-Brass (<200 HB / <700 N/mm2)
- Construction / Carbon Steel (<250 HB / <850 N/mm2)
- Long Chip Copper-Bronze-Brass (<200 HB / <700 N/mm2)
- Al-Mg non-alloyed (<100 HB / <350 N/mm2)
- Alloys Al-Mg Si < 10% (<180 HB / <600 N/mm2)
- Alloys Al-Mg Si > 10% (<180 HB / <600 N/mm2)
- Thermo-Plastics
- 0.040
- 100-130
- 0.040
- 90-120
- 0.035
- 50-100
- 0.035
- 40-60
- 0.025
- 80-100
- 0.040
- 55-70
- 0.040
- 30-50
- 0.020
- 40-55
- 0.050
- 100-250
- 100-250
- 0.080
- 100-300
- 0.080
- 100-300
- 90-200
- 100-200
P.1 Construction / Carbon Steel (<250 HB/<850 N/mm2) Feed (mm/rev.) 0,040 Cutting Speed (m/min.) 100-130
P.2 Alloyed Steel (<300 HB / <1000 N/mm2) Feed (mm/rev.) 0,040 Cutting Speed (m/min.) 90-120
P.3 Treated/Heat-Treatable Alloyed Steel (300-400HB/1000-1300N/mm2) Feed (mm/rev.)0,035 Cutting Speed (m/min.) 50-100
M Austenitic Stainless (<250 HB / <850 N/mm2) Feed (mm/rev.) 0,035 Cutting Speed (m/min.) 40-60
P.5 Ferritic/Martensitic Stainless (320HB/<850 N/mm2) Feed (mm/rev.) 0,025 Cutting Speed (m/min.) 80-100
K.1 Cast Iron (<200 HB / <700 N/mm2) Feed (mm/rev.) 0,040 Cutting Speed (m/min.) 55-70
K.2 Cast Iron (200-300 HB / 700-1000 N/mm2) Feed (mm/rev.) 0,040 Cutting Speed (m/min.) 30-50
S Heat-Resistant Alloys Feed (mm/0,020 Cutting Speed (m/min.) 40-55
N.1 Short Chip Copper-Bronze-Brass (<200 HB / <700 N/mm2) Feed (mm/rev.) 0,050 Cutting Speed (m/min.) 100-250
N.2 Long Chip Copper-Bronze-Brass (<200 HB / <700 N/mm2) Feed (mm/rev.) 0,050 Cutting Speed (m/min.) 100-250
N.3 Al-Mg non-alloyed (<100 HB / <350 N/mm2) Feed (mm/rev.) 0,080 Cutting Speed (m/min.) 100-300
N.4 Al-Mg Si < 10% Alloy (<180 HB / <600 N/mm2) Feed (mm/rev.) 0,080 Cutting Speed (m/min.) 100-300
N.5 Al-Mg Si > 10% Alloy (<180 HB / <600 N/mm2) Feed (mm/rev.) 0,080 Cutting Speed (m/min.) 90-200
N.6 Thermo-Plastics Feed (mm/rev.) 0,030 Cutting Speed (m/min.) 100-200
N.7 Hard-Plastics Feed (mm/rev.) 0,025 Cutting Speed (m/min.) 50-125