04,00 mm-FRESA MICROGRANO DIN6528N 2Z-
14,00 mm-END MILL MICROGRAIN DIN6528N 2Z
- 6528
- N
- Micrograin
- 14.00
- 14.00
- 83.00
- 22.00
- 2
- 30º
- Flat
- 1
- Synthetic-Plastics
- Aluminium-Magnesium
- Cast Iron
- Stainless
- Steel
- Alloyed Steel (<300 HB / <1000 N/mm2)
- Hard-Plastics
- Thermo-Plastics
- Alloys Al-Mg Si > 10% (<180 HB / <600 N/mm2)
- Alloys Al-Mg Si < 10% (<180 HB / <600 N/mm2)
- Al-Mg non-alloyed (<100 HB / <350 N/mm2)
- Construction / Carbon Steel (<250 HB / <850 N/mm2)
- Treated / Heat-Treatable Alloyed Steel (300-400 HB / 1000-1300 N/mm2)
- Austenitic Stainless (<250 HB / <850 N/mm2)
- Ferritic / Martensitic Stainless (<320 HB / <850 N/mm2)
- Cast Iron (<200 HB / <700 N/mm2)
- Cast Iron (200-300 HB / 700-1000 N/mm2)
- Short Chip Copper-Bronze-Brass (<200 HB / <700 N/mm2)
- Long Chip Copper-Bronze-Brass (<200 HB / <700 N/mm2)
- 0.080
- 100-130
- 0.080
- 90-120
- 0.060
- 50-100
- 0.120
- 40-60
- 0.100
- 80-100
- 0.080
- 55-70
- 0.080
- 30-50
P.1 Construction / Carbon Steel (<250 HB/<850 N/mm2) Feed (mm/rev.) 0,080 Cutting Speed (m/min.) 100-130
P.2 Alloyed Steel (<300 HB / <1000 N/mm2) Feed (mm/rev.) 0,080 Cutting Speed (m/min.) 90-120
P.3 Treated/Heat-Treatable Alloyed Steel (300-400HB/850-1300N/mm2) Feed (mm/rev.) 0,060 Cutting Speed (m/min.) 50-100
M Austenitic Stainless (<250 HB / <850 N/mm2) Feed (mm/rev.)0,120 Cutting Speed (m/min.) 40-60
P.5 Ferritic/Martensitic Stainless (320HB/<850 N/mm2) Feed (mm/rev.)0,100 Cutting Speed (m/min.) 80-100
K.1 Cast Iron (<200 HB / <700 N/mm2) Feed (mm/rev.) 0,080 Cutting Speed (m/min.) 55-70
3.2 Cast Iron (200-300 HB / 700-1000 N/mm2) Feed (mm/rev.) 0,080 Cutting Speed (m/min.) 30-50
Cutting Speed (m/min.) 40-55 5.1 Short Chip Copper-Bronze-Brass (<200 HB / <700 N/mm2) Feed (mm/rev.) 0,080
Cutting Speed (m/min.) 100-250 N.2 Long Chip Copper-Bronze-Brass (<200 HB / <700 N/mm2) Feed (mm/rev.) 0,080
Cutting Speed (m/min.) 100-250 N.3 Al-Mg non-alloyed (<100 HB / <350 N/mm2) Feed (mm/rev.) 0,150
Cutting Speed (m/min.) 100-300 N.4 Al-Mg Si < 10% Alloy (<180 HB / <600 N/mm2) Feed (mm/rev.) 0,150
Cutting Speed (m/min.) 100-300 N.5 Al-Mg Si > 10% Alloy (<180 HB / <600 N/mm2) Feed (mm/rev.) 0,150
Cutting Speed (m/min.) 90-200 N.6 Thermo-Plastics Feed (mm/rev.) 0,100
Cutting Speed (m/min.) 100-200 7.2 Hard-Plastics Feed (mm/rev.) 0,080
Cutting Speed (m/min.) 50-125